Skip to main content
    Back to Products

    Poly Aluminium Chloride Liquid

    Al2(OH)nCl6-n
    CAS1327-41-9FormulaAl2(OH)nCl6-nSame-day Muscat · next-day Sohar, Salalah, DuqmSDS + CoA with every batch
    Request a Quote

    Product Overview

    Liquid poly aluminium chloride coagulant for water and wastewater clarification.

    Detailed Description

    Poly aluminium chloride liquid (PAC, CAS 1327-41-9) is a pre-polymerised aluminium coagulant supplied by Global Chemicals LLC at 10–11% Al2O3 with 40–90% basicity, pH 3.5–5.0 in 1% solution, as a clear to light-yellow liquid in 1,000 L IBCs and bulk tanker from stock in Muscat, with jar-test support and dosage optimisation from our technical team. It is widely used in Oman's water plants, and the full grade comparison, specification table and FAQs are on the poly aluminium chloride supplier guide linked on this page; the powder grade is listed separately.

    Why PAC rather than alum. The aluminium in PAC is already polymerised and carries a high positive charge, so it neutralises the charge on turbidity and colour particles and builds floc faster, at lower dose, over a wider pH range (5.0–9.0) and in colder or low-turbidity water than aluminium sulphate. It consumes less alkalinity, so plants need less lime or caustic to hold pH; it leaves less residual aluminium in the treated water; and it produces less, denser sludge. Typical doses run from a few milligrams per litre on clean well water to tens of milligrams per litre on turbid surface water or wastewater, and the jar test sets the figure for each water.

    Where it is used: clarification in municipal and industrial drinking-water plants, primary and tertiary treatment of sewage and industrial effluent, removal of colour and suspended solids from textile and paper wastewater, phosphorus removal, swimming-pool clarification, and pre-treatment ahead of reverse-osmosis desalination, where the dose must be set by jar test and the clarified water filtered so residual aluminium does not reach the membranes.

    Handling and storage: PAC liquid is acidic and corrosive to mild steel; store it in polyethylene, FRP or rubber-lined tanks and dose it with PVC or PE lines and diaphragm pumps, undiluted or diluted just before the dosing point. Keep tanks shaded and closed; the product is stable for six to twelve months and does not freeze in Oman's climate. Wear gloves and goggles. Every delivery carries a certificate of analysis giving Al2O3, basicity, pH and density, plus a GHS safety data sheet.

    Delivery is same day within Muscat, next day to Sohar, two to three days to Salalah and Duqm, by scheduled tanker to treatment plants in every governorate, and by road across the GCC with a certificate of origin. Request a quote with the Al2O3 grade, monthly volume and delivery point.

    Also Known As:

    PAC, Polyaluminium chloride, Polyaluminum chloride, PAC liquid

    CAS Number:1327-41-9

    Applications & Uses

    Drinking water treatment plants
    Wastewater treatment facilities
    Industrial effluent treatment
    Swimming pool water treatment
    Paper manufacturing
    Textile industry wastewater

    Technical Specifications

    Al2O3 content
    10-11%
    Basicity
    40-90%
    pH (1% aqueous solution)
    3.5-5.0
    Appearance
    Clear to light yellow liquid
    Effective pH range
    5.0-9.0

    Frequently Asked Questions — Poly Aluminium Chloride Liquid

    PAC liquid (Poly Aluminium Chloride, 10–11% Al₂O₃) is a pre-dissolved, ready-to-dose coagulant solution, while PAC powder (28–30% Al₂O₃) is a concentrated solid that must be dissolved on-site before dosing. Liquid PAC is preferred for automated dosing systems in large municipal water treatment plants because it can be pumped directly from bulk storage tanks via metering pumps without any dissolution step. The liquid form also provides more consistent dosing accuracy. PAC powder is preferred where liquid storage is impractical, such as remote sites or smaller operations with infrequent deliveries.

    Typical PAC liquid dosing rates range from 10–50 mg/L expressed as product (equivalent to 1–5 mg/L as Al₂O₃). For moderate-turbidity raw water (20–100 NTU) in Oman's groundwater and surface water treatment systems, effective doses are usually 15–30 mg/L of product. Industrial wastewater with high suspended solids or emulsified oil may require 50–150 mg/L. The optimum dose is determined by jar testing. Global Chemicals LLC provides jar test support and dosage optimisation as a standard technical service. Dosing is carried out using chemical metering pumps (peristaltic or diaphragm type) sized to the plant flow rate and expected dosage range.

    Yes. PAC liquid is used as a coagulant in the pre-treatment stage of seawater reverse osmosis (SWRO) plants, where ferric coagulants are the main alternative. In SWRO pre-treatment, PAC is dosed into the raw seawater ahead of pressure media filtration (sand/anthracite) or ultrafiltration (UF) membranes to remove suspended solids, algal cells, and colloidal matter that would otherwise foul the RO membranes. PAC doses in SWRO pre-treatment are typically low (2–10 mg/L product) to avoid residual aluminium carry-over to the membranes. Drinking-water projects that specify NSF/ANSI 60 need a grade certified to that standard, confirmed at quotation.

    PAC liquid should be stored in shaded, covered HDPE or FRP tanks away from direct sunlight to minimise temperature-driven degradation. In Oman's summer conditions (ambient temperatures up to 45°C), exposed tanks can reach 50–55°C, accelerating hydrolysis and basicity shift in the PAC solution, which reduces coagulation performance. Ideal storage temperature is below 35°C. Shelf life is typically 6–12 months from manufacture in correct storage conditions. PAC liquid must not be stored near alkalis (caustic soda, lime) as mixing causes immediate precipitation. Global Chemicals LLC supplies PAC liquid with manufacture date and Al₂O₃ assay certificate, and can advise on tank sizing and storage arrangements.
    ISO 9001 Certified Fast Delivery Oman & GCC Export

    Comparing grades, pack sizes and delivery options? Poly aluminium chloride in Oman — grades, packs and PAC vs alum

    Read the guide

    Request a Quote

    Get pricing, availability, and technical specifications for Poly Aluminium Chloride Liquid. Our team responds within 24 hours.

    Related Products

    Heavy-duty cleaner and degreaser for industrial water treatment.

    View Details

    Technical-grade hydrochloric acid for pH control, descaling, ion-exchange resin regeneration, and metal pickling across Oman's industries.

    View Details

    High-purity sodium chloride for water-softener regeneration, drilling brines, and industrial processing — refined, PVD, and tablet grades.

    View Details

    High-performance adsorbent for removing impurities, odors, and contaminants from water.

    View Details

    Liquid coagulant for efficient flocculation in water and wastewater treatment.

    View Details

    Controls foam in water treatment processes and industrial applications.

    View Details